LED Not Working? A Simple Cabinet Lighting Troubleshooting Guide
A Practical Troubleshooting Guide ·#38
Nine times out of ten, a dead cabinet light is a five-minute fix — not a fault.
Cabinet LED lighting is low-heat, long-life, and remarkably reliable — a quality strip runs for tens of thousands of hours. So when a light suddenly won't come on, the cause is rarely the LED itself. Far more often it's a plug that's worked loose, a switched-off socket, a flat remote battery, or a driver that's simply not getting power.
This guide walks through the checks in the order a technician would — from the quickest, most common causes to the rarer ones — so you can find the problem without pulling anything apart. Work through it top to bottom and stop as soon as the lights come back on.
Start here: the four quick checks
Before opening anything up, run these four checks. They resolve the large majority of “dead” cabinet lights in under a minute each.
-
1
Is it switched on at the wall?
Check the power point the driver is plugged into is switched on, and that nothing else on that circuit has tripped. Test the socket with another device if you're unsure. -
2
Is the plug fully seated?
The barrel plug between the driver and the lead can work loose when a cabinet is moved or cleaned behind. Push it firmly together until it clicks home. -
3
Check the remote battery or Bluetooth app.
Hobbs cabinet lighting is controlled two ways: the Bluetooth app on your phone, or a handheld remote. If you use the remote, a flat battery mimics a dead light perfectly — swap in a fresh AAA and try again. If you use the app, make sure Bluetooth is on and your phone is paired and in range before assuming anything is wrong. -
4
Reset the controller.
The easiest reset is to pull the battery out of the remote, wait a moment, then pop it back in. This clears a controller that's locked up on an “off” or zero-brightness state — the equivalent of turning it off and on again.
Flashing or fading? Check the mode first
This is the most common false alarm of all. If your lights are flashing, strobing, fading or pulsing, nothing is broken — the strip is lit and working perfectly. What's happened is the Mode button on the remote has been pressed by accident, switching the lighting into one of its effect modes.
On a single-colour cabinet, the fix takes seconds: on the remote, turn the brightness up to 100%, which brings it back to a steady, full-strength light. Once it's solid again, you're done — there was never a fault to fix.
If it's flickering, check the wiring is tight
Our LEDs don't flicker in normal use — a steady, constant light is how they run. So a true flicker (not one of the effect modes above) almost always means a wire hasn't been seated fully or a terminal has worked slightly loose.
Check every connection is properly wired in and secure. Where the wiring lands on a screw terminal, a small screwdriver to firm up each terminal is usually all it takes — make sure the wire is gripped, not just resting, and that nothing has pulled part-way out. Once every connection is tight, the flicker settles and the light holds steady.
If part of the strip is dead
Every Hobbs cabinet is lit with a single continuous run of LED — one full length, with no joints, connectors or soldered welds anywhere along it. That's deliberate: joins are the number-one failure point in cheaper lighting, and we design them out. It also means you'll never get the “one connector has dropped out” problem, because there are no connectors to drop out.
So if part of the strip is dark while the rest lights — most obvious on RGB, where a dead patch stands out straight away — the strip itself has been physically damaged, not disconnected. A damaged LED run can't be repaired or spliced back to life; the length is simply replaced. The good news is it's an inexpensive, self-contained part, and swapping a full run is quick and clean. Send us your cabinet model and we'll match the exact strip.
If nothing lights at all
A completely dark cabinet points upstream, to the power supply. Every Hobbs cabinet runs on a professional 12 volt low-voltage power supply — the proper way to light a glass display cabinet. Low voltage is safe to work around (there's no dangerous mains voltage at the strip) and it's stable, so a supply that's healthy has no reason to simply stop delivering. That's why a dark cabinet nearly always traces back to the mains side — a switched-off socket or tripped circuit — rather than the low-voltage supply itself.
Check the driver itself: many have a tiny indicator light that tells you it's live. Feel whether it's slightly warm — stone cold usually means it isn't receiving power, so return to the wall-switch and socket checks above. If you have a second compatible driver of the same voltage and rating, swapping it in is the fastest way to confirm whether the driver has failed. A driver is an inexpensive, plug-in part and is by far the most common component to replace — not the LED strip.
One thing worth ruling out: an overloaded driver. If lights were added to the cabinet over time, the total strip length may now exceed what the driver is rated to run, which can leave it unable to start. Matching the driver to the strip length fixes it.
Checking the transformer is the right size
A transformer must be rated comfortably above the total load it carries. The rule professionals work to: only load it to about 80–90% of its rated wattage, never right up to 100%. That headroom keeps it running cool and reliable for years. So a 100 watt transformer should really only be asked to carry around 80 to 90 watts.
Working out the numbers is simple. The system is 12 volt, and watts = volts × amps — so multiply 12 by the transformer's amp rating to get its wattage capacity. Then add up what the cabinet actually draws.
Against that ~90–95 watt load, we supply a 120W or 150W transformer — well above the draw, with the safety headroom already built in. If you're ever unsure whether a replacement transformer is suitable, check its 12V amp rating, multiply out the wattage, and confirm it clears your total load with room to spare.
A few things not to do
Don't spray glass cleaner near the strip — moisture is a common cause of flicker and corrosion, and it's why we always say to spray the cloth, never the cabinet. Don't kink, fold or pull hard on the strip, as that's what physically damages a run. And don't force a stiff plug or over-bend a lead; if a connection resists, something is misaligned rather than needing more pressure.
If you've worked through every check and the cabinet still won't light, it comes down to one of two replaceable parts — the driver or the LED strip itself — not a whole-cabinet problem. Send us the model and a photo of the setup and we'll identify the exact part you need.
Need a replacement part or a fully-lit cabinet?
We supply, deliver, and install across Perth and Australia-wide. Call us on 08 6237 1039, or visit us at 325 Victoria Road, Malaga WA 6090 — Mon–Fri 9am–5pm, Sat 10am–2pm AWST.